Resources:
Datasheet
FT231XQ-R USB 2.0 Full-Speed to UART Bridge Interface IC with 3 Mbaud Data Rate and 20-Pin QFN Package
The FT231XQ-R is a compact USB-to-UART bridge interface IC from FTDI, designed to provide reliable asynchronous serial communication between USB-enabled devices and embedded electronic systems. Supporting USB 2.0 Full-Speed communication at 12 Mbps and UART data rates from 300 baud to 3 Mbaud, this single-chip controller enables efficient USB-to-serial data transfer without requiring USB-specific firmware development. Its full-handshake UART interface, integrated USB protocol handling, and compatibility with FTDI Virtual COM Port (VCP) and D2XX drivers make it well-suited for microcontroller programming, industrial communication, USB-to-serial converters, and embedded system development.
Designed for compact PCB applications, the FT231XQ-R features a 20-pin QFN package with integrated clock generation, eliminating the need for an external crystal. It incorporates 2048 bytes of Multi-Time-Programmable (MTP) memory for device configuration, along with 512-byte transmit and receive buffers for efficient data handling. The controller also supports configurable CBUS I/O, USB battery-charger detection, UART signal inversion, and flexible power configurations. With a typical operating current of 8 mA, USB suspend current of 125 uA, and an operating temperature range of -40 to +85 deg C, the FT231XQ-R provides a low-power USB connectivity solution for industrial and embedded applications.
Key Features
- USB-to-UART Bridge: Provides single-chip USB-to-asynchronous-serial communication for embedded systems and microcontroller applications.
- USB 2.0 Full-Speed Interface: Supports USB Full-Speed communication at 12 Mbps for compatibility with USB-enabled host devices.
- High-Speed UART Communication: Supports serial data rates from 300 baud to 3 Mbaud for efficient serial data transfer.
- Full-Handshake UART Interface: Supports UART hardware-handshaking signals for controlled serial communication.
- Integrated USB Protocol Handling: Manages the USB protocol internally without requiring USB-specific firmware development.
- 2048-Byte MTP Memory: Stores USB device descriptors and configurable CBUS I/O settings.
- Built-In Clock Generation: Eliminates the requirement for an external crystal and supports optional clock-output functionality.
- 512-Byte TX/RX Buffers: Includes separate 512-byte transmit and receive buffers with buffer-smoothing technology.
- FTDI Driver Support: Compatible with royalty-free Virtual COM Port (VCP) and Direct (D2XX) drivers.
- Configurable CBUS I/O: Provides programmable CBUS pins for application-specific control and status functions.
- Transmit and Receive LED Support: Supports TX and RX activity-indication signals through configurable CBUS functionality.
- Flexible UART Configuration: Supports 7-bit or 8-bit data, 1 or 2 stop bits, and odd, even, mark, space, or no parity.
- Bit-Bang Interface Modes: Supports synchronous and asynchronous bit-bang operation with RD# and WR# strobes.
- USB Battery-Charger Detection: Detects compatible USB charging sources to support external charging-control circuitry.
- Unique USB Serial Number: Includes a factory-programmed unique serial number for device identification.
- Flexible USB Power Options: Supports bus-powered, self-powered, and high-power bus-powered USB configurations.
- Configurable Logic-Level Interface: Provides 3.3V CMOS output, 5V-tolerant inputs, and 1.8V interfacing with suitable external pull-up resistors.
- Integrated Voltage Regulators: Includes internal 3.3V and 1.8V LDO regulators for device operation.
- Low-Power Consumption: Features 8 mA typical active current and 125 uA typical USB suspend current.
- Integrated Power-On Reset: Provides internal reset functionality for reliable device start-up.
- UART Signal Inversion: Supports configurable UART signal inversion for different interface requirements.
- Industrial Temperature Range: Operates from -40 to +85 deg C for industrial and embedded environments.
- Compact QFN Package: Supplied in a lead-free, RoHS-compliant 20-pin QFN package for surface-mount PCB assembly.
Applications
- USB-to-UART converter modules and adapter circuits
- Microcontroller programming and debugging interfaces
- Embedded systems and development boards
- Industrial serial communication equipment
- USB-based data acquisition and monitoring systems
- UART communication with microcontrollers and FPGAs
- USB-to-RS232, RS422, and RS485 converters with external transceivers
- USB-enabled instrumentation and diagnostic equipment
- Legacy serial peripheral upgrades
- Custom electronic devices requiring USB connectivity