Resources:
Datasheet
CP2105-F01-GMR USB 2.0 Full-Speed to Dual UART Bridge Interface IC with 2 Mbps Data Rate and 24-Pin QFN Package
The CP2105-F01-GMR is a highly integrated USB-to-dual-UART bridge interface IC from Silicon Labs, designed to provide reliable serial communication between USB-enabled computers and embedded electronic systems. Featuring a USB 2.0 Full-Speed interface and 2 independent UART channels, this single-chip controller enables simultaneous communication with multiple serial devices through a single USB connection. Its Enhanced UART supports data rates up to 2 Mbps, while the Standard UART operates up to 921600 bps. The integrated USB transceiver, clock oscillator, and programmable memory simplify hardware development, making it well-suited for microcontroller programming, industrial communication, embedded systems, and USB-to-serial converter applications.
Designed for compact and efficient PCB integration, the CP2105-F01-GMR features a 4 x 4 mm 24-pin QFN package with an integrated USB controller, internal voltage regulator, and 296-byte one-time-programmable memory for device configuration. It supports configurable UART logic levels from 1.8V to VDD, hardware and software flow control, and general-purpose I/O functions for flexible system integration. Silicon Labs Virtual COM Port (VCP) and USBXpress driver support simplifies host-side communication, while the -40 to +85 deg C operating temperature range makes the device suitable for industrial automation, diagnostic equipment, and embedded applications requiring dual-channel serial connectivity.
Key Features
- USB-to-Dual-UART Conversion: Provides 2 independent asynchronous UART interfaces through a single USB connection for communicating with multiple serial devices.
- USB 2.0 Full-Speed Interface: Supports USB Full-Speed communication at 12 Mbps for reliable connectivity with compatible USB hosts.
- Enhanced UART Performance: Supports programmable baud rates from 300 bps to 2 Mbps for high-speed serial communication.
- Standard UART Interface: Supports data rates from 2400 bps to 921600 bps for additional serial communication requirements.
- Integrated USB Transceiver: Includes USB communication circuitry and eliminates the need for external USB termination resistors.
- Internal Clock Oscillator: Features integrated clock generation, eliminating the need for an external crystal.
- Programmable ROM: Incorporates 296 bytes of one-time-programmable memory for custom USB device descriptors, identification, and interface configuration.
- Independent UART Buffers: Includes 320-byte transmit and receive buffers for the Enhanced UART and 288-byte transmit and receive buffers for the Standard UART.
- Flexible Flow Control: Supports hardware RTS/CTS flow control, software X-On/X-Off flow control, and operation without flow control.
- Configurable Logic Levels: Supports UART and GPIO logic levels from 1.8V to VDD through a dedicated VIO pin.
- Enhanced UART Configuration: Supports 5, 6, 7, or 8 data bits, multiple parity modes, and configurable stop-bit settings.
- RS485 Control Support: Provides an Enhanced UART mode for controlling an external RS485 transceiver.
- General-Purpose I/O: Features up to 5 configurable GPIO signals for application-specific status and control functions.
- Driver Compatibility: Supports Silicon Labs Virtual COM Port (VCP) and USBXpress direct-access drivers.
- Integrated Voltage Regulator: Includes an internal regulator to simplify USB bus-powered system designs.
- Power-On Reset: Features an integrated reset circuit for controlled device start-up.
- USB Suspend Support: Provides suspend-state signalling for USB power-management applications.
- Industrial Temperature Range: Supports operation from -40 to +85 deg C.
- Compact QFN Package: Supplied in a 24-pin, 4 x 4 mm QFN package for space-constrained PCB layouts.
Applications
- USB-to-dual-UART converter modules
- Microcontroller programming and debugging interfaces
- Embedded systems and development boards
- Industrial serial communication equipment
- Dual-channel data acquisition and monitoring systems
- USB-enabled diagnostic and test equipment
- UART communication with microcontrollers and FPGAs
- USB-to-RS232 and RS485 interface designs with external transceivers
- Legacy serial device connectivity and upgrades
- Industrial automation and control systems
- Custom electronic equipment requiring multiple serial interfaces