Resources:
Datasheet
TXS0102DCTR 2-Bit Bidirectional Voltage-Level Translator with Auto-Direction Sensing and 24 Mbps Push-Pull Support
The Texas Instruments TXS0102DCTR is a 2-bit, non-inverting bidirectional voltage-level translator designed to provide digital logic compatibility between mixed-voltage systems. It uses separate A-side and B-side supply rails, with the A ports operating from 1.65–3.6 V and the B ports from 2.3–5.5 V, allowing translation between common 1.8 V, 2.5 V, 3.3 V, and 5 V logic domains. Automatic direction sensing eliminates the need for a separate DIR control pin, simplifying interfaces where signal direction can change dynamically.
The TXS0102 supports both open-drain and push-pull signals, with data rates up to 2 Mbps for open-drain operation and 24 Mbps for push-pull operation. Integrated 10 kOhm pull-up resistors and edge-rate accelerator circuitry support bidirectional interfaces such as I2C, SMBus, UART, and GPIO. An active-high output-enable input places all I/O pins in a high-impedance state when low, while VCC isolation and partial-power-down support help prevent unwanted current paths during system power sequencing.
Key Features
- 2-Bit Bidirectional Translation: Provides 2 independent non-inverting channels for mixed-voltage digital interfaces.
- Automatic Direction Sensing: Determines signal direction automatically without requiring a dedicated DIR pin.
- 1.65–3.6 V A-Port Supply: Supports low-voltage logic levels, including 1.8 V, 2.5 V, and 3.3 V systems.
- 2.3–5.5 V B-Port Supply: Supports higher-voltage logic interfaces including 2.5 V, 3.3 V, and 5 V systems.
- Mixed-Voltage Compatibility: Enables translation between common 1.8 V, 2.5 V, 3.3 V, and 5 V voltage nodes.
- 24 Mbps Push-Pull Data Rate: Supports high-speed push-pull digital signals at up to 24 Mbps.
- 2 Mbps Open-Drain Data Rate: Supports bidirectional open-drain interfaces at up to 2 Mbps.
- Open-Drain and Push-Pull Support: Suitable for I2C/SMBus as well as selected UART and GPIO applications.
- Integrated 10 kOhm Pull-Ups: Internal pull-up resistors are provided on both A-side and B-side I/O pins.
- Edge-Rate Accelerators: One-shot circuitry improves rising-edge speed and overall data-rate capability.
- Active-High Output Enable: OE pin provides direct control over device enable and high-impedance operation.
- High-Impedance Disable Mode: Pulling OE low places all I/O pins into the high-impedance state.
- VCC Isolation: If either supply is at GND, both I/O ports enter the high-impedance state.
- No Supply Sequencing Required: VCCA or VCCB can be powered or ramped first.
- Partial-Power-Down Support: Ioff circuitry supports systems where one supply domain is powered down.
- Low Static Supply Current: Combined supply current is specified up to approximately 14.4 uA under static test conditions.
- High B-Port ESD Protection: B-side pins are rated up to ±8 kV HBM.
- Industrial Temperature Range: Specified for operation from -40°C to +85°C.
- Compact SSOP-8 Package: DCT package offers a small surface-mount footprint for space-limited designs.
- Tape-and-Reel Packaging: TXS0102DCTR is supplied in 3,000-piece reels for automated PCB assembly.
Applications
- I2C interfaces
- SMBus interfaces
- UART communication
- GPIO level translation
- Mixed-voltage microcontroller systems
- Sensor interfaces
- Processor-to-peripheral communication
- Embedded systems
- Battery-powered electronics
- Portable devices
- Consumer electronics
- Industrial control systems
- IoT devices
- Development boards
- Logic-level conversion