Description
This ready-to-run system is a complete solution for your embedded project needs. It integrates a clock circuit, USB power management, USB connector, and other features, so you can get started right away. The onboard 64M Bit SDRAM provides ample memory for your applications, and the JTAG/SWD programming/debugging interface makes it easy to program and debug your code. All the I/O ports are accessible on the pin headers, with a 2.0mm header pitch that allows it to be easily plugged into your application board.
-
Minimal ready-to-run system, integrates clock circuit, USB power management, USB connector, etc.
-
Onboard 64M Bit SDRAM
-
All the I/O ports are accessible on the pin headers
-
JTAG/SWD programming/debugging interface
-
2.0mm header pitch, allowed to be plugged-in your application board
-
Core746I x 1
-
USB type A plug to micro B plug cable x 1
-
Software CD x 1
- Schematic
- Demo code (examples in C, FreeRTOS, uC/OS-III)
- STM32 development software (KEIL, STM32CubeMX, etc.)
- STM32 datasheets
- STM32 development documentations
What's on the Core746I
- STM32F746IGT6: the high performance STM32 MCU which features:
- Core: Cortex-M7 32-bit RISC + FPU + Chrom-ART graphic accelerator
- Feature: single-cycle DSP instructions
- Operating Frequency: 216MHz, 462 DMIPS/2.14 DMIPS/MHz
- Operating Voltage: 1.7V-3.6V
- Package: LQFP176
- Memories: 1024kB Flash, 320+16+4kB SRAM
- MCU communication Interfaces:
- 6 x SPI, 4 x USART, 4 x UART, 3 x I2S, 4 x I2C
- 2 x CAN, 1 x QUAD-SPI, 1 x DCMI, 2 x SAI
- 1 x FMC, 1 x SDMMC, 14 x TIM , 1xLPTIM
- 1 xLCD-TFT, 1xSPDIFRX, 1xHDMI-CEC
- 1 x USB 2.0 OTG FS
- 1 x USB 2.0 OTG HS (supports external HS PHY through ULPI)
- 1 x 10/100 Ethernet MAC
- AD & DA converters: 3 x AD (12-bit); 2 x DA (12-bit)
- Debugging/Programming: supports JTAG/SWD interfaces, supports IAP
- IS42S16400J: SDRAM 1 Meg Bits x 16 Bits x 4 Banks (64-MBIT)
- MIC2075: onboard USB power management device
- AMS1117-3.3: 3.3V voltage regulator
- 8M crystal
- 32.768K crystal, for internal RTC with calibration
- Reset button
- VBUS LED
- Power indicator
- Power supply switch, powered from 5Vin or USB connection
- Boot mode selection, for configuring BOOT0 pin
- JTAG/SWD interface: for debugging/programming
- USB connector, supports Device and/or Host
- MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion
- Power jumper
- VBAT: short the jumper to use system power supply, open it to connect external power, such as battery
- VREF: short the jumper to connect VREF+ to VCC, open it to connect VREF+ to other custom pin via jumper wire
- OTG jumper
- short the jumper when using USB OTG/HOST
- open the jumper to disconnect from related I/O port
Dimensions
Q: What is the processor used in the CORE746I board?
A: The CORE746I board features the high-performance STM32F746IGT6 microcontroller, which has an ARM Cortex-M7 core.
Q: What are the memory specifications of this development board?
A: The board comes equipped with 1MB of Flash memory and 340kB of SRAM for code and data storage.
Q: What display interfaces are supported?
A: The CORE746I board supports RGB LCD interfaces through a parallel port and also includes an onboard 40-pin FPC connector for displays.
Q: What connectivity options does the board offer?
A: The board provides a variety of connectivity options, including Ethernet, USB HS/FS, MicroSD card slot, and multiple UART interfaces.
Q: Are there additional features like a camera interface?
A: Yes, the board includes a dedicated 8-bit parallel CMOS camera interface for image processing applications.
