STM32 small board with the STM32F407ZxT6 MCU

The Core407Z STM32 Development Board is a small and ready-to-run system that features an STM32F407ZxT6 microcontroller, which is part of the STM32F family. It is ideal for application development and supports further expansion. The board integrates a USB communication interface, JTAG/SWD programming/debugging interface, clock circuit, USB power management, boot mode selection, and more. Additionally, the pin headers on the backside of the board allow it to be easily plugged into an application board and serve as the MCU core circuit in your system. All I/O ports are accessible on the pin headers, and the header pitch is designed as 2.00mm.

• Microcontroller: STM32F407ZxT6
• USB Communication Interface: Yes
• JTAG/SWD Programming/Debugging Interface: Yes
• Clock Circuit: Yes
• USB Power Management: Yes
• Boot Mode Selection: Yes
• Pin Headers: Yes (2.00mm pitch)
• System Integration: Yes
• Ready-to-Run: Yes
• Expansion Support: Yes

1. Core407Z development board x 1
2. USB type A to Mini-B cable x 1
3. Software CD x 1

What's On Board

• STM32F407ZxT6 (STM32F407ZET6 by default):the high performance STM32 MCU which features:
  • Core: Cortex-M4 32-bit RISC
  • Feature: a full set of single-cycle DSP instruction
  • Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
  • Operating Voltage: 1.8V-3.6V
  • Package: LQFP144
  • Memories: 512kB/1024kB Flash, 192+4kB SRAM
  • MCU communication Interfaces:
    • 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C
    • 1 x FSMC, 1 x SDIO, 2 x CAN
    • 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
    • 1 x 10/100 Ethernet MAC
    • 1 x 8 to 14-bit parallel camera interface
• AD & DA converters: 3 x AD (12-bit, 1us, shares 24 channels); 2 x DA (12-bit)
• Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
• AMS1117-3.3 (on bottom side): 3.3V voltage regulator
• MIC2075 (on bottom side): onboard USB power management device
• Power supply switch, powered from 5Vin or USB connection
• Boot mode switch, for configuring BOOT0 pin
• Power indicator
• VBUS LED
• Reset button
• 8M crystal oscillator (on bottom side)
• 32.768K crystal (on bottom side), for internal RTC with calibration
• JTAG/SWD interface: for debugging/programming
• USB interface
  • as DEVICE, used for establishing USB communication between PC and the STM32 development board
  • as HOST, connecting to USB devices such as USB flash drive through a USB OTG cable
• MCU pins expander, VCC, GND and all the I/O ports are accessible on expansion connectors for further expansion
• 5Vin pinheader, 5V power supply is required when using USB HOST/OTG
• USB HOST/OTG jumper
  • short the jumper when using USB HOST/OTG
  • open the jumper to disconnect from I/O port
• VBAT selection jumper
  • short the jumper to use system power supply
  • open the jumper to connect the VBAT to external power, such as battery
• VREF selection jumper
  • short the jumper to connect VREF+ to VCC
  • open the jumper to connect VREF+ to other custom pin via jumper wire

Dimensions

Photos